Six-Axis Force Sensor Parts We Have Machined: Aluminum Flexures, Housings and Flanges

Based on the aluminum six-axis force sensor parts Zhongde Precision has machined (flexure bodies, housings and covers, mounting flanges and adapter plates), this article explains thin-beam distortion, strain gauge surfaces, mounting faces, inspection and what to send for a quote.

Published:November 16, 2026 Updated:November 16, 2026 7 min read
In This Article

Need joint housings or robot parts? Upload drawings for a quote

Direct Answer

Zhongde Precision has machined the following aluminum parts for six-axis force sensors.

PartFunctionMachining focus
Flexure bodyDeforms under load; strain gauges detect the strainBeam thickness, symmetry, gauge surfaces, distortion
Housing and top and bottom coversProtects the flexure and electronics; overload stopThin walls, clearances, sealing faces, cable exit
Mounting flanges and adapter platesConnects to the robot side and the tool sideFace parallelism, dowel holes, bolt holes, coaxiality

Under our confidentiality agreements, we do not publish customer names, drawings or part photos. This article only describes the part types and what we watched while machining them.


1. How a Six-Axis Force Sensor Is Built

A six-axis force sensor measures three forces (Fx, Fy, Fz) and three moments (Mx, My, Mz) at the same time. At its center is the flexure body, a single metal part with cross-shaped or spoke-shaped beams. Under load, the beams deform slightly. Strain gauges bonded to the beams turn that deformation into electrical signals, and calibration separates the signals into six components.

Around the flexure are a housing and covers that protect it and the electronics. Flanges or adapter plates on the top and bottom connect the sensor to the parts on either side. Many designs leave a small gap in the housing that acts as an overload stop to protect the beams.

Sensor accuracy does not depend only on the gauges and electronics. Consistent flexure geometry and flat, parallel mounting faces are what keep the zero point stable and cross-talk between axes low.

2. The Parts Zhongde Has Machined

Zhongde Precision has machined the three part types in the table above, all in aluminum alloy.

Gauge bonding and calibration are normally done by the sensor maker. Machining creates what those steps depend on: geometry, surfaces and cleanliness. So we plan the process not only to meet drawing dimensions, but also so that sensors do not vary from one to the next after bonding and calibration.

3. Machining the Flexure Body

3.1 Keep Thin Beams from Deflecting

Beams are designed thin to get sensitivity. Thin beams deflect under cutting force, and differences in tool wear or depth of cut turn directly into thickness differences. For finishing, we use small depths of cut and sharp tools, and machine every beam under the same conditions and in the same sequence.

3.2 Leave No Machining Distortion

Removing a lot of material from an aluminum block releases residual stress and changes the shape. We remove most of the stock in roughing, let the part rest, and separate roughing from finishing to reduce distortion after finishing. If thin beams or walls are finished while clamped hard, they spring back when released, so workholding is part of process design.

3.3 Measure Symmetry

Separating the six components assumes every beam has the same stiffness. One thicker beam changes the sensitivity in that direction and causes cross-talk. We measure the thickness and position of every beam on a coordinate measuring machine and check the variation.

3.4 Gauge Surfaces and Beam Roots

Gauge surfaces need to be flat, with consistent roughness and no burrs, dents or tool steps. The fillets at the beam roots affect stress concentration, so we keep their shape consistent and avoid steps where tool passes meet.

3.5 Cleanliness and Packaging

Cutting oil or coolant residue affects gauge bonding. Parts are washed and dried, then packed so the beams and gauge surfaces cannot be dented.

4. Machining Housings and Covers

Housings tend to have thin walls, so distortion and dimensional variation need attention. The gap that acts as an overload stop is designed around the deflection of the flexure, which makes the housing dimensions and the assembled position important.

Where dust or water protection is needed, we control the flatness and roughness of sealing faces and the dimensions of O-ring grooves. The position and shape of the cable exit also matter for cable bending and protection. If the housing is anodized or otherwise finished, the drawing should define the dimensional change from the coating and the masking of any grounding points.

5. Machining Mounting Flanges and Adapter Plates

Flanges connect the sensor to the robot side and the tool side. The flatness and parallelism of the top and bottom faces and the position of dowel and bolt holes are the datums that align the sensor axis with the mating axis. A warped or non-parallel mounting face puts extra load on the sensor when the bolts are tightened, which shows up as zero drift and differences between reassemblies.

If the robot-side interface follows a standard such as ISO 9409-1, we use those dimensions as the datum and make their relationship to the sensor-side holes clear on the drawing.

6. Why Aluminum, and What to Watch

Aluminum alloy is light, easy to machine and makes sensitivity easier to achieve at low load ranges. That suits places such as humanoid robot wrists and ankles, where mass at the end of the limb should be kept low.

Compared with steel and titanium, aluminum has lower strength and fatigue strength and higher thermal expansion. For high loads or long-term cyclic loading, stainless steel or titanium is generally chosen. The customer chooses the material and temper from the rated load, overload and temperature conditions, and we plan the process for that material.

7. Inspection

The main inspection items are listed below. Specific tolerances differ by part and material and are set from the drawing and inspection standard.

ItemWhat we check
Flexure beamsThickness, position and symmetry of every beam
Gauge surfacesFlatness, roughness, burrs, dents and steps (magnified)
Mounting facesFlatness and parallelism of top and bottom faces
HolesPosition of dowel holes and bolt holes
HousingThin-wall dimensions, sealing faces, overload gap
Cleanliness, appearanceOil and coolant residue, dents, packaging condition

8. How This Relates to Humanoid Robots

Humanoid robots put six-axis force sensors in the wrists and ankles to measure grip force and ground reaction force. The key points for sensor parts, finishing thin structures without distortion, keeping mounting faces flat and parallel, and keeping variation between axes and between left and right parts small, are the same for joint housings, flanges and foot frames.

How force sensors are used in the foot is covered in how humanoid robot feet are manufactured, and the critical characteristics of joint parts in CTQs for joint actuator precision parts.

9. What to Send for a Quote or Samples

New projects can start with samples. Send us the following, and we will confirm the machining and inspection approach before quoting.

ItemDetails
Drawings3D model (STEP or similar) and 2D drawing
MaterialAluminum alloy grade and temper
QuantitySample quantity and expected production volume
Gauge surfacesRoughness, whether finishing is allowed, restrictions
Surface finishAnodizing or not, color, masked areas
InspectionKey dimensions, measurement methods, report format
PackagingCleanliness, individual packing, dent protection

Frequently Asked Questions

Which six-axis force sensor parts has Zhongde Precision machined?

Aluminum flexure bodies, housings and top and bottom covers, and mounting flanges and adapter plates. Under our confidentiality agreements, we do not publish customer names, drawings or part photos.

What is the most important point when machining a flexure body?

Thin beams deflect under cutting and clamping forces, and residual stress can change the shape after machining. We separate roughing from finishing, finish every beam under the same conditions, and measure the thickness and position of all beams to confirm symmetry.

What do strain gauge bonding surfaces need?

They need to be flat, with consistent roughness, no burrs, dents or tool steps, and no oil or coolant residue. The required roughness and whether a surface finish is allowed are specified on the drawing, and we confirm them against gauge bonding and calibration results during sampling.

Can all force sensor parts be made of aluminum?

Our experience is with aluminum parts. In general, aluminum is common for lightweight, low-capacity sensors, while stainless steel or titanium is used for high loads or high fatigue strength. The customer chooses the material from the rated load, overload and temperature conditions, and we plan the process for that material.

Can we start with samples?

Yes. We make a small quantity from your drawings first, and volume production follows once machining, finishing and inspection are confirmed. Please send the 3D model, 2D drawing, material, quantity and requirements for the gauge surfaces.

Related Articles

Related Capabilities

Related Topics

  • six-axis force sensor
  • flexure body
  • force sensor parts
  • aluminum CNC machining
  • machining distortion
  • humanoid wrist and ankle
  • project experience

Technical Review: Zhongde Precision Engineering Team

Have Drawings to Review?

Upload your drawings. Our engineering team will provide a manufacturing review and quotation within 24 hours.

Upload Drawings / Get a Quote
Fast Response
Engineering Review
Data Security
Reliable Delivery
Contact Us